The Wiki for Tale 5 is in read-only mode and is available for archival and reference purposes only. Please visit the current Tale 11 Wiki in the meantime.

If you have any issues with this Wiki, please post in #wiki-editing on Discord or contact Brad in-game.

Difference between revisions of "Glass Blowing"

From ATITD5
Jump to navigationJump to search
Line 21: Line 21:
 
==== Ariella ====
 
==== Ariella ====
 
*'''Standard Heat'''
 
*'''Standard Heat'''
 +
 +
Make sure that your chat is minimized and that you PUT YOUR CURSOR ON THE GLORY HOLE before starting your keystrokes.
  
 
*aaaaaaaaaa sssssss mmmmmmmmm bbbb mmmmmmm q mmmm u  That's about it.
 
*aaaaaaaaaa sssssss mmmmmmmmm bbbb mmmmmmm q mmmm u  That's about it.
Line 32: Line 34:
 
*TO REPAIR and bring less than 3500 quality up
 
*TO REPAIR and bring less than 3500 quality up
 
**Rotate until droop of bulb is pointing up and stop rotating a couple clicks to let it droop back to normal while hitting 'q'.  You can often improve the quality enough to save it this way. ~Ariella~
 
**Rotate until droop of bulb is pointing up and stop rotating a couple clicks to let it droop back to normal while hitting 'q'.  You can often improve the quality enough to save it this way. ~Ariella~
 
  
 
==Hookah Bowl==
 
==Hookah Bowl==

Revision as of 02:49, 15 September 2010

WARNING: The Push and Pull hotkeys are reversed on the menu from the way they actually operate. A is push (into the GH), S is pull (out of the GH). Also, like all buildings with hotkeys, your mouse cursor must be touching the actual building in order for the hotkeys to register.

Hotkeys

  • G - Goal Display
  • A - Moves the project into the glory hole
  • S - Moves the project out of the glory hole
  • Q - Check the current quality
  • N - Rotate counterclockwise
  • M - Rotate clockwise
  • U - Unload (complete) the project
  • D - Discard the project, destroying the materials
  • B - Blow into the tube

Thermometers

Requires: 1 Glass Pipe, 1 Quicksilver

You must have Advanced Glassblowing & Basic Chemestry for thermo to show up in the gloryhole list.

Method

Ariella

  • Standard Heat

Make sure that your chat is minimized and that you PUT YOUR CURSOR ON THE GLORY HOLE before starting your keystrokes.

  • aaaaaaaaaa sssssss mmmmmmmmm bbbb mmmmmmm q mmmm u That's about it.
  1. 'a' held down to push it in clear to the back.
  2. Hit 's' EXACTLY 7 times to pull it back out.
  3. Rotate hitting 'm' til you see the frontish part turn a bit yellow.
  4. Hit 'b' EXACTLY 4 times to blow the bulb.
  5. Rotate with 'm' again until your pinky can hit 'q' to check the quality.
  • Keep checking until it's over 3500 and hit 'u' quick as you can after you see that.
  • TO REPAIR and bring less than 3500 quality up
    • Rotate until droop of bulb is pointing up and stop rotating a couple clicks to let it droop back to normal while hitting 'q'. You can often improve the quality enough to save it this way. ~Ariella~

Hookah Bowl

Requires: 1 Fine Glass Rod

File:Hookah Bowl.jpg

Methods

  • Pin Point Heat
  1. Constantly spin to keep entire piece centered (there is a correct rhythm to spin it's not just spinning as fast as you can)
  2. Start the bowl shape at the bottom
  3. Move the glass in 2 times
  4. Move the glass in 3 times pausing between each
  5. blow 4 times
  6. Move the glass all the way inside the glory hole
  7. Make the mouth of the bowl
  8. Move the glass out 5 times
  9. blow 2 times
  10. Move the glass out 2 and then in 2 (turning the section just under the mouth brown/orange not yellow)
  11. blow 4 to 6 times
  12. Make the ridged middle body of the bowl
  13. Move the glass out 2 times
  14. Move the glass out 3 times (very quickly) (pause 'till this section is orange)
  15. Move the glass out 1 time (pause 'till orange)
  16. Move the glass out 3 times slowly pausing such that each segment just barely turns yellow (you want these 3 segments to heat up at the same time, so as you get better you can go back and forth over this area)
  17. Repeat over the next 3 segments
  18. Blow 2-3 times