Yeast Testing

Yeast testing is a function of beer brewing, using the "Yeast Test" option on the Beer Kettle. It is used to determine the distribution of microbes at the kettle location. The overall goal of yeast testing is to find a location where the first microbe to enter the kettle is a yeast, and then (usually) to discover a seal time at that location where only that yeast (or that yeast along with other yeasts) gets in.

How to Find and Isolate a Yeast

The 100 microbes in the game (including the 51 useful yeasts) are distributed all across Egypt. The distribution of microbes at a specific location, and their entry times, are fixed throughout the telling (i.e. microbes don't "drift" around over time, nor are they affected by pollution or other outside factors). Once you find a useful yeast spot, you can always count on it being there. But first you have to find them.

A "good yeast spot" is one where the first microbe to appear is a yeast. By placing kettles in different locations and performing yeast tests, you will eventually find such spots. (Because yeasts comprise 51 of the 100 possible microbes, it should not take too terribly long to locate one.) Of course, some yeasts are "better" than others -- they produce more alcohol or make an interesting flavor -- but when you're just starting out as a brewer, any yeast is good. Convenience matters as well: a mediocre yeast that happens to exist right inside your camp, near your supplies and all your stuff, can be more useful than a fancy high-alcohol yeast that you have to run into the middle of nowhere to access.

You isolate a yeast by running a Yeast Test. This kettle option is a shortcut that eliminates the brewing phase, thus taking only 40 minutes to complete. At the end of the test, you take the 'beer' (you need your small barrel!) and get a display of the results. At the bottom is a list of the microbes that are in the kettle, in the order they entered (first to last).

1. Run a yeast test (The Yeast option, which takes 25 water, 60 wood, 2400 Teppy seconds (about 44.25 minutes real time)), leaving the lid open until the end. If the first microbe in the list is not a yeast, start over in another spot. Don't forget to have a small barrel with you so you can get the results of the yeast test!
2. Once you find somewhere where at least the first microbe is a yeast, run a new yeast test, closing the lid at 1200 seconds (the halfway point of the fermentation phase).
3. If the results show no microbes, it means you have closed the lid too soon; run a new test and close the lid at 600 seconds (remaining). If the results show more than one microbe, run another yeast test and close the lid at 1800 seconds to see if you have isolated the time when the first yeast enters the kettle.
4. Keep running yeast tests, dividing the times when the yeast might have entered in half, until you get only the first yeast. This tells you your sealing time when making beer -- close the lid at the same time as you did in this successful test so that only this first yeast will be active in your beer.

Microbes appear to enter the kettle on seconds divisible by 12. It is possible for two or more microbes to enter simultaneously.

NOTE: If you are in a spot where the second (or more) microbes are also yeasts, you may also want to try making multi-yeast beer by finding the seal time that gets you only 2 yeasts (or 3, etc, up to however many you have). While the results of multiple-yeast brews are hard to predict, some people have successfully used the beerCalc tool to do this. Moreover, many beers made without sealing the lid are effectively multi-yeast beers, and you can find many such recipes and locations on the Wiki (do a search for your yeast -- e.g., search for Y3 to find pages with recipes for that yeast).

#Yeast Map - please report the locations of the microbes you find in the map above!

Microbe Transition Lines

Hellinar - Inspired by Jaby's work on large scale microbe distribution, I've been testing the changes in microbe distribution on small scales. These tests demonstrate that the microbe population shifts as your kettle crosses coordinate lines. The degree of shift is dependent on the degree to which the coordinate is divisible by two. Thus if the coordinate you cross is divisible by 128, most of the upper microbes will change. On the other hand if the coordinate can only be divided by 8, or 4 or 2, the shift in order is likely to be small. This shift occurs very sharply within a small fraction of a coordinate. So avoid placing kettles on such a high power of two coordinate. On the other hand, if you are searching for new microbes, place four kettles on odd numbered coordinates around the point where two lines divisible by 128 cross. This will give you four sets of well shuffled microbes.